Geruchsfreier und faserverstärkter 2 Komponenten-Harz. Dieser Kunststoff kan mit einem Pinsel oder Spachtel tropffrei an senkrechten Flächen angewendet werden. Die Bearbeitungszeit beträgt 8-10 Minuten, die Aushärtungszeit ist 90 Minuten.
- Geeignet für starke und leichte Unterstützung oder Stützformen
- Geeignet für Verstärkung hinter einem Gelcoat von Shell Shock
Digitale keukenweegschaal. Weegt tot 2kg op 1 gram nauwkeurig. Exclusief batterij.
20,21 EUR(incl. 21% USt. zzgl. Versand)
Informations
Preparation – Materials should be stored and used in at room temperature 23° C. This product has a limited shelf life and should be used as soon as possible. Mixing should be done in a wellventilated area. Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk. If making a 2 or more piece mother mold, apply appropriate shim apparatus to rubber mold exterior.
Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.
Applying A Release Agent – This product is adhesive and will bond to many surfaces. A sealer followed by a release agent is necessary to facilitate demolding when applying as a mother mold over a cured mold rubber. Use Sonite™ Wax followed by a coating of Universal™ Mold Release or Ease Release 200 release agent. A liberal coat of release agent should be applied onto all surfaces that will contact the plastic. You can also apply aluminum foil as a barrier over the surface followed by an application of Mold Release agent.
PRE-MIX Part B Before You Start – Part B is a thick paste containing oil that needs to be pre-mixed before being dispensed into measuring container. Dig deep to re-disperse oil & paste components that may have separated.
Measuring – The components of Plasti-Paste™ requires two different sized containers. The first will be used for measuring out amounts of Part A and Part B. The second should be large enough to contain both components and allow thorough mixing. IMPORTANT: Shelf life of Part A (Yellow Container) is reduced after opening. Remaining product should be used as soon as possible. XTEND-IT™ Dry Gas Blanket will prolong shelf life of unused liquid urethanes.
Mixing – Mix Ratio is 1A:3B by volume (41A:100B by weight). (Step 1) Fill measuring container to the top with Part B paste, making sure to eliminate any air voids. Level off the top of the container and remove any excess material. The paste should then be thoroughly emptied into a larger container that will act as your mixing container. Repeat As Necessary. (Step 2) Fill the measuring container to the top with Part A liquid and empty into mixing container. Mix thoroughly for 2-3 minutes making sure that you scrape the sides and bottom of the mixing container several times. Eliminate color streaks. If adding So-Strong™ color tints, pre-mix color with the Part B before adding Part A.
Mixing Large Batches - A ‘Turbine’ mechanical mixer attached to a power drill will make mixing large batches of material much easier.
IMPORTANT: Shelf life of product is reduced after opening. Remaining product should be used as soon as possible. Immediately replacing the lids on both containers after dispensing product will help prolong the shelf life of the unused product. XTEND-IT™ Dry Gas Blanket (available from form X) will significantly prolong the shelf life of unused liquid urethane products.
Applying – Mixed material thickens quickly and pot life is limited. Do not delay between mixing and applying. To increase working time, spread entire container contents over rubber mold surface and cover and spread mixture to uncovered areas. Apply uniformly with spatula over mold surface. Material will adhere to itself if additional layers are needed. Apply at least 1 cm thickness, making sure rubber mold is thoroughly covered. For maximum strength and heat resistance, 1.27 cm thickness is recommended. Large molds may require added thickness for support shell stability. Supports (wood or metal) may be embedded for added stability and handling. Prevent a jagged surface; Final layer of Plasti-Paste™ can be smoothed by wiping solvent (denatured alcohol or acetone) onto surface with gloved hand.
Making A Two Piece Shell – Plasti-Paste™ will bond to most surfaces and itself tenaciously. A barrier coat of paste wax followed by Universal™ Mold Release applied to all surfaces is necessary to prevent adhesion. Applying aluminum foil to the contours of all surfaces followed by Universal™ Mold Release will also prevent adhesion.
Curing – Plastic will be hot immediately following cure. Let cool to room temperature before handling. Material will develop handling strength and can be handled in about 90 minutes depending on mass. At this point, it is stable enough to demold, re-assemble over rubber mold and make a casting (hold 2 or more piece assemblies together with elastic bands, mold straps or bolts). Large sections should be bolted together to minimize distortion. Full strength develops in 24 hours.
Heat Resistance – Fully cured plastic with a minimum thickness of (1.27 cm) will resist temperatures up to 55°C. To improve heat resistance to 70°C, post cure material at 65°C for 16 hours.
If machining or sanding cured plastic, wear NIOSH approved mask to prevent inhalation of residual particles.
Storage – For best storage results, cast into rubber mold with a gypsum plaster or other dimensionally stable material, assemble mold inside the Plasti-Paste™ support shell and store assembled molds on a level surface indoors at room temperature in a dry place.
Comfortable and easy to wear paint spray mask. By making a minimum of components. Easy cleaning Due to the large surface area of the filters, a very low breathing resistance arises. The filters a...
COLAD spray mask is a disposable mask with two active carbon cartridges that protect against the inhalation of organic solvents. The COLAD spray mask should be replaced after 40 hours by a new spra...
The Supergloves Bluple nitrile disposable glove is made from top quality nitrile. The Bluple nitrile is, despite its smaller thickness (3.2 mil.), Strong and particularly comfortable due to its hig...
The Supergloves Bluple nitrile disposable glove is made from top quality nitrile. The Bluple nitrile is, despite its smaller thickness (3.2 mil.), Strong and particularly comfortable due to its hig...
The Supergloves Bluple nitrile disposable glove is made from top quality nitrile. The Bluple nitrile is, despite its smaller thickness (3.2 mil.), Strong and particularly comfortable due to its hig...
The Supergloves Bluple nitrile disposable glove is made from top quality nitrile. The Bluple nitrile is, despite its smaller thickness (3.2 mil.), Strong and particularly comfortable due to its hig...
Sempercare's examination gloves are suitable for all medical and nursing procedures. These gloves...
11,01 EUR(incl. 21% USt. zzgl. Versand)
Trennmittel
Trennmittel
ACMOS 82-2405
Trennmittel in einer Sprühflasche. Geeignet für Polyester, Epoxidharze, PMMA und Polyurethane. Für die Herstellung von Formen. more
AquaCon™
AquaCon™ is a water based concrete release agent that aids in releasing concrete castings from Smooth-On rubber molds and other surfaces such as melam ... more
Ease Release®
EASE RELEASE 205 is a versatile liquid release agent that is used for a variety mold making and casting applications. This product will release liquid ... more
Ease Release® 2831
Ease Release® 2831 is a wax-based non-silicone release agent. It has proven to be effective when used to release polyurethane foams elastomers. Ease R ... more
In & Out® II
IN & OUT® II water soluble release agent will aid in releasing concrete or gypsum plaster castings from Smooth-On rubber molds. IN & OUT® II provides ... more
One Step™
One Step™ is a convenient, economical liquid sealing agent and release agent in one. This low odor, low viscosity formula is offered as a “one step” a ... more
Plaster Seperator
Gipstrennmittel zur Verwendung bei Gips-gegen-Gips-Anwendungen. more
To facilitate removal of materials from the Denture Duplicator Flask and other metal surfaces. more
Universal Mold Release
Universal® Mold Release Agent is formulated especially for mold making and casting, and works well with most liquid rubber and liquid plastic products ... more
Es wurden keine Produkte gefunden, die Ihren Kriterien entsprechen. Wählen Sie andere Filter-Optionen.
*Alle Preise incl. Umsatzsteuer, zuzüglich
Hilfe bei der Auswahl
Produkte nach Anwendung sortiert, z. B.:Lifecasting, Bildhauerei, Gießen, Special FX Make-up, Zahnprothesen Special FX, Studium.
Wir verwenden Cookies um unsere Website zu optimieren und Ihnen das bestmögliche Online-Erlebnis zu bieten. Mit dem Klick auf "Alle akzeptieren" erklären Sie sich damit einverstanden. Erweiterte Einstellungen