Warenkorb anzeigen (0 Artikel) Mein KontoMerkzettel anzeigenZur Kasse gehen

Brush-On 35

Kaufen Sie Smooth-On bei FormX

Smooth-On ist einer der weltweit führenden Hersteller von 3D-Modellierungsmaterialien wie Formenbau-, Gieß- und Spezialeffektmaterialien, industrielle Gießharze, Klebstoffe und Ausrüstung. FormX ist Vertriebspartner von Smooth-On-Produkten in Europa.

Brush-On 35

Leicht zu mischen und mit einem Pinsel oder Spachtel an zu bringen, BRUSH-ON 35 Farben sind auf senkrechten Flächen an zu bringen und Harte mit vernachlässigbarer Schrumpfung zu einer dauerhaften Gummi, die in der Produktion führt.

Gängige Anwendungen für BRUSH-ON 35 sind: Vor-Ort Formen für architektonische Restaurierung, Reproduktione von Skulpturen (Kunst Bronze Wachsformen - Wachsausschmelzverfahren) und Special Effects.

technical Bulletin

Shore: 35 A

Safety Brush-On part B

- Lesen Sie das Sicherheitsinformationsetikett. Klicken Sie auf das Bild.

- Read the safety information label. Click on the image

- Lisez les informations de sécurité cliquez sur l'image

- Lea la etiqueta de información de seguridad. Haga clic en la imagen

- Lees het veiligheidsinformatie label. Klik op de afbeelding.

Products

Brush-On 35

  • Brush-On™ 35 /6kg

    Shore: 35 A

    174,17 EUR

  • Brush-On™ 35 /34kg

    Shore: 35 A

    856,03 EUR

Making a hard/flexible composite mold

zusammengesetzte flexible / harte Form

Brush-On 35 kann sehr gut in Kombination mit Plasti-Paste verwendet werden, um eine Verbundform mit einem flexiblen Innenraum und einem harten Außen zu schaffen. Eine solche Form wird durch Anlegen der Plasti-Paste über die Brush-On Form gemacht, ohne das dazu ein Trennmittel verwendet werden muss. Die beiden Urethan-Materialien werden sich verkleben und nun zusammen eine feste Verbundschicht erzeugen. Eine solche Form ist für große Gussteile von zum Beispiel Beton sehr geeignet.

Eine Verbundform herstelle, BO-35 und Plasti-Paste

Instructions

Preparation - Materials should be stored and used in at room 23°C. Humidity should be low. These products have a limited shelf life and should be used as soon as possible. Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk. Good ventilation (room size) is necessary.

Some Materials Must Be Sealed - To prevent adhesion between the rubber and model surface, models made of porous materials (gypsum plasters, concrete, wood, stone, etc.) must be sealed prior to applying a release agent. SuperSeal™ or One Step™ available from form X are fast drying sealers suitable for sealing porous surfaces without interfering with surface detail. Shellac is suitable for rough contours. A high quality spray shellac is suitable for sealing modeling clays that contain sulfur or moisture (water based). Thermoplastics (polystyrene) must also be sealed with shellac or PVA.

In all cases, the sealing agent should be applied and allowed to completely dry prior to applying a release agent.

Non-Porous Surfaces - Metal, glass, hard plastics, sulfur free clays, etc. require only a release agent.

Applying A Release Agent - A release agent is necessary to facilitate demolding when casting into or over most surfaces. Use a release agent made specifically for mold making (Universal™ Mold Release available from form x). A liberal coat of release agent should be applied onto all surfaces that will contact the rubber.

IMPORTANT: To ensure thorough coverage, lightly brush the release agent with a soft brush over all surfaces of the model. Follow with a light mist coating and let dry for 30 minutes. Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

IMPORTANT: Shelf life of product is reduced after opening. Remaining product should be used as soon as possible. Immediately replacing the lids on both containers after dispensing product will help prolong the shelf life of the unused product. XTEND-IT™ Dry Gas Blanket (available from Smooth-On) will significantly prolong the shelf life of unused liquid urethane products.

MEASURING & MIXING - Liquid urethanes are moisture sensitive and will absorb atmospheric moisture. Mixing tools and containers should be clean and made of metal, glass or plastic. Materials should be stored and used in a warm environment 23°C.

Mixing - Part A is a paste with the consistency of cake frosting. Fill a container to the top with this paste, making sure to eliminate any large voids. Level off the top of the container and remove any excess material. The paste should then be thoroughly emptied into a larger container that will act as your mixing container. Next, fill the original container to the top with Part B (liquid) and empty it into the mixing container. After dispensing equal amounts of Parts A and B into mixing container, mix thoroughly for 3 minutes making sure that you scrape the sides and bottom of the mixing container several times.

Applying The Rubber - This product must be applied in layers. Mold makers generally find that four to six layers (minimum 3/8”) thickness is suitable for a working mold. Using a stiff brush, the first coat of rubber should be applied in a thin layer to capture intricate detail. Use dabbing strokes, especially around undercuts, to reduce entrapped air. Subsequent coats will add strength to the mold. Let the first coat dry for 30-40 minutes at room temperature or when it becomes “tacky” before adding the next coat. Repeat until the necessary thickness is achieved. Do not allow rubber to fully cure between layers, as delamination may result. Note: Although not necessary, adding a small amount of SO-Strong™ liquid color pigment available at form X to every other mix of rubber will help you distinguish one layer from the next. This will ensure that you apply a thorough coating each time and help build uniform layers.

Curing - Allow rubber to cure overnight (at least 16 hours) at room temperature 23°C before demolding. Cure time can be reduced with mild heat or by adding Smooth-On “Kick-It™” Cure Accelerator. Do not cure rubber where temperature is less than 18°C.

Post Curing - After rubber has cured at room temperature, heating the rubber to 65°C for 4 to 8 hours will increase physical properties and performance.

Apply A Support Shell - Once the mold is fully cured, a rigid support shell (mother mold) is needed to support the rubber mold during casting. Plasti-Paste™ II is a trowelable plastic which is ideal as a mother mold material.

Using The Mold - If using as a mold material, a release agent should be applied to the mold before each casting. The type of release agent to use depends on the material being cast. The proper release agent for wax, liquid rubber or thermosetting materials (i.e. Smooth-On liquid plastics) is a spray release made specifically for mold making (available from Smooth-On or your distributor). Prior to casting gypsum plaster materials, sponge the mold with a soap solution for better plaster flow and easy release. In & Out™ II Water Based Release Concentrate available from form x is recommended for releasing abrasive materials like concrete.

Performance & Storage - Fully cured molds are tough, durable and will perform if properly used and stored. The physical life of the mold depends on how you use it (materials cast, frequency, etc.). Before storing, the mold should be cleaned with a soap solution and wiped fully dry. Two part (or more) molds should be assembled. Molds should be stored on a level surface in a cool, dry environment. Do not stack molds, expose them to moisture or UV light.

++

You might also need...

  • Mixing Beakers
  • Measuring Cups & Jars
  • Weighting devices
  • Brushes
  • Protective Gear such as gloves
  • Release agents
Pinsel

Pinsel

  • flat brush 30mm

    flache Einwegbürsten

    0,80 EUR

  • flat brush 40mm

    flache Einwegbürsten

    0,92 EUR

  • flat brush 50mm

    flache Einwegbürsten

    1,39 EUR

  • flat brush 60mm

    flache Einwegbürsten

    1,38 EUR

  • flat brush 70mm

    flache Einwegbürsten

    1,39 EUR

  • Calupaint Platte 40mm

    Calupaint Platte 40mm

    2,60 EUR

  • polyesterkwast 20mm

    polyester brush 20mm round

    3,09 EUR

  • polyesterkwast 25mm

    polyester brush 25mm round

    3,51 EUR

  • houten polyesterkwast 35mm

    houten polyesterkwast 35mm

    2,21 EUR

  • houten polyesterkwast 50mm

    wooden polyester brush 50mm flat

    3,46 EUR

  • Polyester kwast plat 75mm

    Polyester brush, Flat, 75 mm

    3,33 EUR

  • Pinsel 40mm, holz, blank

    Brush, flat, 40mm, wooden handle.

    2,84 EUR

Schutzkleidung

Sicherheit

  • 3M safety glasses Classic

    3M safety glasses Classic

    15,19 EUR

  • Glove Nitrile M

    Glove Nitrile M

    11,01 EUR

  • Glove Nitrile XL

    Glove Nitrile XL

    11,01 EUR

  • Glove Nitrile L

    Glove Nitrile L

    11,01 EUR

  • Glove Nitrile S

    Glove Nitrile S

    11,01 EUR

  • 3M 06941 Halfgelaatmasker

    3M 06941 Halfgelaatmasker

    50,53 EUR

  • Paint spray mask Colad

    Easy to wear paint spray mask

    35,39 EUR

  • Filter ABEK1 for 3M 6200 maskers

    Protection against chemicals vapors

    36,87 EUR

  • Stenchmask carbon fibre

    Stenchmask carbon fibre

    5,41 EUR

Mischen, Messen & Wiegen

Messen, Wiegen und Mischen

Mixing

  • Measuring cup /30ml

    Measuring cup 30ml + graduation

    0,19 EUR

  • Measuring cup /125ml

    Measuring cup 125 ML + Graduation

    0,48 EUR

  • Measuring cup /350 ml

    Mixing and measuring beaker

    0,57 EUR

  • Measuring cup /700 ml

    Mixing and measuring beaker

    0,63 EUR

  • Measuring cup /1400 ml

    Mixing and measuring beaker

    0,80 EUR

  • Measuring cup /2300 ml

    Mixing and measuring beaker

    1,46 EUR

  • SO mixing cup /473ml

    SO mixing cup /16oz

    1,04 EUR

Mixing

  • SO mixing cup /946ml

    SO mixing cup /32oz

    1,09 EUR

  • SO mixing cup /1892ml

    SO mixing cup /64oz

    2,84 EUR

  • SO mixing cup /4880ml

    SO mixing cup /165oz

    3,35 EUR

  • Mixing beaker /1000ml

    plastic mixing beaker 1162 ml

    0,64 EUR

  • Mixing beaker round /500ml

    Mixing Beaker, Round, Polypropylene, 500 cc contents

    0,25 EUR

  • Mixing Bowl square /2000ml

    180x180 mm

    0,91 EUR

  • Flexible mixing cup /500ml

    Flexible mixing bowl for gypsum, alginate etc. 500 ml

    8,05 EUR

Mixing

  • Flexible mixing cup /1750ml

    Flexible mixing bowl for gypsum, alginate etc. 1750 ml

    19,34 EUR

  • Injektionsspritze mit

    Katheterspitze /50ml

    5,76 EUR

  • Wooden tongue spatula

    with rounded ends

    3,42 EUR

  • Mixing stick small

    220x17x3 mm

    0,05 EUR

  • Mixing stick big

    300x20x4 mm

    0,24 EUR

  • Turbine Mixer

    Turbine Mixer

    16,11 EUR

  • Colad Turbomix /per 200

    Paint stirrers Professional per 200 stirrers in dispenser.

    61,38 EUR

  • Tristar KW2430 Scale

    Digitale keukenweegschaal. Weegt tot 2kg op 1 gram nauwkeurig. Exclusief batterij.

    20,21 EUR

Trennmittel

Trennmittel

Spray Releases

  • Safety Info Acmos

  • Acmos 82 aerosol /400gr

    Trennmittel in einer Sprühflasche. Geeignet für Polyester, Epoxidharze, PMMA und Polyurethane. Fü...

    20,63 EUR

  • Ease Release 200 aerosol /400gr

    Removable aerosol release agent - silicone based - 400 gram spraycan

    19,54 EUR

  • Ease Release 300 aerosol /400gr

    for PU, epoxy, polyester, RTV silicones and thermoplastics.

    18,22 EUR

Spray Releases

  • Safety Info Ease Release Group

  • Ease Release 400 aerosol /400gr

    Removable aerosol release agent - silicone based - spraycan 400grams

    21,33 EUR

  • Ease Release 500 aerosol /400gr

    Removable aerosol release agent - silicone based - spraycan 400 gram

    22,30 EUR

Spray Releases

  • Safety Info Universal Mold Release

  • Universal Mold Release aerosol /400gr

    Silicon based Universal release agent - aerosol, without ozone gas - spraycan 400 grams

    17,05 EUR

  • Kwikee Sprayer

    946 ml Pressure Sprayer

    138,57 EUR

Hilfe bei der Auswahl

Produkte nach Anwendung sortiert, z. B.:Lifecasting, Bildhauerei, Gießen, Special FX Make-up, Zahnprothesen Special FX, Studium.

FormX Newsletter FormX Mitteilungsblatt Über uns Kontakt Transportoptionen Kundenprojekte AGB Wir haben offene Stellen Anwendungsbereich Branches FormX Academy

Ihr One-Stop-Shop für 3D-Modelling-Materialien

Wir verwenden Cookies um unsere Website zu optimieren und Ihnen das bestmögliche Online-Erlebnis zu bieten. Mit dem Klick auf "Alle akzeptieren" erklären Sie sich damit einverstanden. Erweiterte Einstellungen